Join NeutronX on Telegram
Guides

What is a TWAP order? TWAP vs POV explained

NeutronX team

· 2:28

· 2:28

0:00 / 2:28

What is a TWAP order? TWAP vs POV explained · 2:28

In this video

Buying a large crypto position with one market order means taking every price in the order book until the size is filled. The bigger the order, the further up the book it goes and the worse the average price gets. A TWAP order (time-weighted average price) splits that order into equal parts and sends them one by one at a fixed interval, so your entry ends up close to the average price over that time. On NeutronX you can use TWAP on every perpetual futures market.

How TWAP works

You choose how many parts to split the order into and how long to wait between them. The first part goes out one interval after you place the order, the next one after another interval, and so on until all of them are sent. Each part is a market order inside the market's price band around the mark price (±0.5% for BTC).

In the video the order is split into 2 parts with 28 blocks between them. A block takes about 0.9 seconds, so that is roughly 24 seconds per pause and under a minute for the whole order. On a real trade you would usually spread it out more: 10 parts every 10 minutes, for example, take a little under two hours.

TWAP and POV

Both split a large order. They just decide the size of each part differently. TWAP keeps to a schedule, with equal parts at equal intervals whatever the market is doing. POV watches the volume and trades a share of it, so it buys more when the market is busy and less when it is quiet. If the order has to be done by a certain time, TWAP is the simpler choice. If you would rather your order did not stand out from the flow of trades, look at POV.

The settings

There are three numbers, and the third one follows from the first two:

  • Slices: how many parts the order is split into, from 2 to 100.

  • Interval: the pause between slices, in blocks. The form has presets of about 24 seconds, 2 minutes, 10 minutes and 1 hour.

  • Duration: slices times interval. The form works it out and shows it in the order summary.

TWAP has no price limit, so every slice trades at the market. If you need a cap on the price, use a limit order or a POV with a price limit.

How to place a TWAP order

The video starts with 100 USDC in the trading account and opens a long on BTC.

  1. Go to Trading. TWAP is under More in the order panel on the right.

  2. Set the leverage. At 10× the margin is the position size divided by 10.

  3. Tap 100% for the size. At 10× that is a 998.30 USDC position, about 0.0154 BTC.

  4. Set slices to 2 and the interval to 28 blocks, about 24 seconds.

  5. Look at the summary under the form: the order runs for about 47 seconds in 2 slices of 0.00772 BTC and needs 99.83 USDC of margin. Tap Long BTC · TWAP · 10×.

  6. In the confirmation window check the size, the slices and the time, the margin, the 0.50 USDC fee and the liquidation price, which is 58,462 here, 9.5% below the entry. Confirm the long.

Tip

Tick "Don't ask for TWAP and POV orders" and this window won't show up next time. You can bring it back in Settings.

What happens next

A bar above the chart shows how far the order has got. The first slice goes out and opens half of the position, then the order waits another 28 blocks and sends the second one. In the video the two slices filled at 64,586.40 and 64,617.56, only $31 apart, and the position opened at an average entry of 64,601.98.

You can cancel a running TWAP at any time, but you can't edit it. To change the settings, cancel the order and place a new one.

Good to know

  • A slice can fill only partly if the order book doesn't have enough inside the price band. The missing part is added to the last slice, and whatever the last slice can't fill stays unfilled.

  • Each slice has to meet the market's minimum order size, so a small order can't be cut into many slices.

  • While a market is paused, slices wait and go out once trading resumes. During a trading halt, TWAP orders that open a position wait too.

  • With Reduce-only a TWAP closes a position in parts and stops once the position is closed.

  • Every slice pays the taker fee of your tier.

  • Up to 20 TWAP orders can run at the same time.

Risk

Splitting an order changes how you enter a position, not how risky it is. At 10× on the whole balance, a move of about 9.5% against you is enough to liquidate it, as in the video. Pick a leverage you are comfortable with.

FAQ

What is a TWAP order?

A TWAP (time-weighted average price) order splits a large order into equal slices and sends them at a fixed interval, so the entry lands close to the average price over that time.

TWAP vs POV: which one to use?

TWAP follows the clock: equal parts on a schedule, finished by a known time. POV follows the volume and trades a share of what the market trades. Use TWAP when timing matters and POV when you want the order to blend into the flow of trades.

How many slices and what interval should I pick?

More slices with longer pauses spread the order thinner and take longer to finish. Start from how long you are willing to wait, since the duration is slices times interval, and keep each slice above the market's minimum order size.

What happens if a slice doesn't fill?

If a slice fills only partly, the rest is added to the last slice. If the last slice can't fill everything either, that part stays unfilled and the order ends with what it has bought.

Try TWAP on NeutronX

exchange.neutronx.com/trading
Try it on the exchange